A model order reduction method based on the component mode synthesis for mistuned bladed disks is introduced, with one component for the disk and one component for each blade. The interface between the components at the blade roots is reduced using the wave-based substructuring (WBS) method, which employs tuned system modes. These system modes are calculated first, and used subsequently during the reduction of the individual components, which eliminates the need to build a partially reduced intermediate model with dense matrices. For the disk, a cyclic Craig–Bampton (CB) reduction is applied. The deviations of the stiffness and mass matrices of individual disk sectors are then projected into the cyclic basis of interior and interface modes of the disk substructure. Thereby, it is possible to model small disk mistuning in addition to large mistuning of the blades.
Issue Section:
Gas Turbines: Structures and Dynamics
References
1.
Castanier
, M. P.
, and Pierre
, C.
, 2006
, “Modeling and Analysis of Mistuned Bladed Disk Vibration: Current Status and Emerging Directions
,” J. Propul. Power
, 22
(2
), pp. 384
–396
.2.
Yang
, M.-T.
, and Griffin
, J. H.
, 2001
, “A Reduced-Order Model of Mistuning Using a Subset of Nominal System Modes
,” ASME J. Eng. Gas Turbines Power
, 123
(4
), pp. 893
–900
.3.
Lim
, S.-H.
, Bladh
, R.
, Castanier
, M. P.
, and Pierre
, C.
, 2007
, “Compact, Generalized Component Mode Mistuning Representation for Modeling Bladed Disk Vibration
,” AIAA J.
, 45
(9
), pp. 2285
–2298
.4.
Sinha
, A.
, 2009
, “Reduced-Order Model of a Bladed Rotor With Geometric Mistuning
,” ASME J. Turbomach.
, 131
(3
), p. 031007
.5.
Madden
, A.
, Epureanu
, B. I.
, and Filippi
, S.
, 2012
, “Reduced-Order Modeling Approach for Blisks With Large Mass, Stiffness, and Geometric Mistuning
,” AIAA J.
, 50
(2
), pp. 366
–374
.6.
Vargiu
, P.
, Firrone
, C. M.
, Zucca
, S.
, and Gola
, M. M.
, 2011
, “A Reduced Order Model Based on Sector Mistuning for the Dynamic Analysis of Mistuned Bladed Disks
,” Int. J. Mech. Sci.
, 53
(8
), pp. 639
–646
.7.
Beck
, J. A.
, Brown
, J. M.
, Kaszynski
, A. A.
, Cross
, C. J.
, and Slater
, J. C.
, 2015
, “Geometric Mistuning Reduced-Order Models for Integrally Bladed Rotors With Mistuned Disk–Blade Boundaries
,” ASME J. Turbomach.
, 137
(7
), p. 071001
.8.
Pohle
, L.
, 2017
, Schwingungsverhalten verstimmter zyklischer Systeme und deren optimierung durch bewusste Verstimmung
, Leibniz Universität Hannover and TEWISS—Technik und Wissen GmbH, Garbsen.9.
Hohl
, A.
, Siewert
, C.
, Panning
, L.
, and Wallaschek
, J.
, 2010
, “A Substructure Based Reduced Order Model for Mistuned Bladed Disks
,” ASME
Paper No. DETC2009-87459
. 10.
Tran
, D.-M.
, 2001
, “Component Mode Synthesis Methods Using Interface Modes. application to Structures With Cyclic Symmetry
,” Comput. Struct.
, 79
(2
), pp. 209
–222
.11.
Bampton
, M. C. C.
, and Craig, JR
, R. R.
, 1968
, “Coupling of Substructures for Dynamic Analyses
,” AIAA J.
, 6
(7
), pp. 1313
–1319
.12.
Salas
, M. G.
, Bladh
, R.
, Mårtensson
, H.
, Petrie-Repar
, P.
, Fransson
, T.
, and Vogt
, D. M.
, 2017
, “Forced Response Analysis of a Mistuned, Compressor Blisk Comparing Three Different Reduced Order Model Approaches
,” ASME J. Eng. Gas Turbines Power
, 139
(6
), p. 062501
.13.
Sternchüss
, A.
, and Balmes
, E.
, 2006
, “On the Reduction of Quasi-Cyclic Disk Models With Variable Rotation Speeds
,” International Conference on Noise and Vibration Engineering (ISMA
), San Diego, CA, May 10–12, pp. 3925–3940https://www.sdtools.com/pdf/isma06_cyclic.pdf.14.
Bladh
, R.
, Castanier
, M. P.
, and Pierre
, C.
, 2001
, “Component-Mode-Based Reduced Order Modeling Techniques for Mistuned Bladed Disks—Part I: Theoretical Models
,” ASME J. Eng. Gas Turbines Power
, 123
(1
), pp. 89
–99
.15.
Craig
, R.
, and Chang
, C.
, 1977
, “Substructure Coupling for Dynamic Analysis and Testing
,” National Aeronautics and Space Administration, Washington, DC, Report No. NASA-CR-2781
https://ntrs.nasa.gov/search.jsp?R=19770010568.16.
Balmès
, E.
, 1996
, “Use of Generalized Interface Degrees of Freedom in Component Mode Synthesis
,” Office National D'études Et De Recherches Aérospatiales
, Châtillon-Sous-Bagneux, France.17.
Zhang
, G.
, Castanier
, M. P.
, and Pierre
, C.
, 2004
, “Efficient Component Mode Synthesis With a New Interface Reduction Method
,” 22nd International Modal Analysis Conference (IMAC), Dearborn, MI
, pp. 2043
–2055
.18.
Carassale
, L.
, and Maurici
, M.
, 2017
, “Interface Reduction in Craig–Bampton Component Mode Synthesis by Orthogonal Polynomial Series
,” ASME J. Eng. Gas Turbines Power
, 140
(5
), p. 052504
.19.
Donders
, S.
, Pluymers
, B.
, Ragnarsson
, P.
, Hadjit
, R.
, and Desmet
, W.
, 2010
, “The Wave-Based Substructuring Approach for the Efficient Description of Interface Dynamics in Substructuring
,” J. Sound Vib.
, 329
(8
), pp. 1062
–1080
.20.
Castanier
, M. P.
, Tan
, Y.-C.
, and Pierre
, C.
, 2001
, “Characteristic Constraint Modes for Component Mode Synthesis
,” AIAA J.
, 39
(6
), pp. 1182
–1187
.21.
Aoyama
, Y.
, and Yagawa
, G.
, 2001
, “Component Mode Synthesis for Large-Scale Structural Eigenanalysis
,” Comput. Struct.
, 79
(6
), pp. 605
–615
.22.
Gibanica
, M.
, Abrahamsson
, T. J.
, and Rixen
, D. J.
, 2017
, “A Reduced Interface Component Mode Synthesis Method Using Coarse Meshes
,” Procedia Eng.
, 199
, pp. 348
–353
.23.
Kurstak
, E.
, and D'Souza
, K.
, 2017
, “Multistage Blisk and Large Mistuning Modeling Using Fourier Constraint Modes and Prime
,” ASME
Paper No. GT2017-63835
. 24.
Sternchüss
, A.
, 2009
, “Multi-Level Parametric Reduced Models of Rotating Bladed Disk Assemblies
,” Ph.D. dissertation, École Centrale Paris, Paris, France.Copyright © 2019 by ASME
You do not currently have access to this content.
