Intravenous catheterization is the most common invasive medical procedure today and is designed to introduce medication directly into the blood stream. Common practice is to administer medicine with one syringe, followed by a saline flush to clear the line of any residual medication. The risk of infection due to the introduction of bacteria in the catheter hub is increased with the number of times the hub is accessed. In addition, the two-step process adds millions of nursing hours per year and is prone to error. The goal of this effort was to design and test a dual-chamber syringe that could be reliably used for both dispensing medicine and the saline flush, and be produced at a low cost. The syringe has a novel dual-chamber design with a proximal chamber for medicine and a distal chamber that contains saline. The saline chamber has a fixed volume when the handle is locked into position, which allows the handle to control the variable volume of the medicine chamber. Between the two chambers is a plunger that surrounds the small channel (which is an extension of the distal chamber) that separates the saline from the medicine. When the distal chamber is unlocked, the handle controls the volume of the saline chamber. By this mechanism, the syringe is able inject the medicine followed by the saline flush with a single access to the catheter hub. The smooth operation of the device relies on a locking mechanism to control the rear plunger and volume of the distal saline chamber, and a bubble plug residing in the small channel between the chambers that prevents mixing of the medicine and saline fluids. The bubble plug is held in place by a balance of forces that depend on geometric variables and fluid properties. The chosen design prevents mixing of the two fluids during the operation of the device, which was experimentally validated with mass spectrometry. The dual-chamber syringe has successfully achieved the design goal of a single syringe for the two-step catheter procedure of dispensing medicine and a saline flush. This novel design will reduce the potential for catheter-based infection, medical errors, medical waste, and clinician time. Preliminary test results indicate that this innovation can significantly improve the safety and efficiency of catheter-based administration of medicine.
Skip Nav Destination
e-mail: kmaynewm@mail.sdsu.edu
Article navigation
June 2011
Research Papers
Design and Preliminary Testing of a Novel Dual-Chambered Syringe
Karen May-Newman,
Karen May-Newman
Department of Mechanical Engineering, Bioengineering Program,
e-mail: kmaynewm@mail.sdsu.edu
San Diego State University
, San Diego, CA 92181-1323
Search for other works by this author on:
Maria T. Matyska,
Maria T. Matyska
San Jose State University
, San Jose, CA 95192
Search for other works by this author on:
Martin N. Lee
Martin N. Lee
Preventiv, Inc.
, Sacramento, CA
Search for other works by this author on:
Karen May-Newman
Department of Mechanical Engineering, Bioengineering Program,
San Diego State University
, San Diego, CA 92181-1323e-mail: kmaynewm@mail.sdsu.edu
Maria T. Matyska
San Jose State University
, San Jose, CA 95192
Martin N. Lee
Preventiv, Inc.
, Sacramento, CAJ. Med. Devices. Jun 2011, 5(2): 021003 (5 pages)
Published Online: June 17, 2011
Article history
Received:
October 21, 2010
Revised:
February 18, 2011
Online:
June 17, 2011
Published:
June 17, 2011
Citation
May-Newman, K., Matyska, M. T., and Lee, M. N. (June 17, 2011). "Design and Preliminary Testing of a Novel Dual-Chambered Syringe." ASME. J. Med. Devices. June 2011; 5(2): 021003. https://doi.org/10.1115/1.4003822
Download citation file:
Get Email Alerts
Cited By
Validation of a Repurposed pH Monitoring Capsule for Cecal Applications Using Novel Synthetic Cecal Contents
J. Med. Devices (March 2025)
Related Articles
Multifunction Pericardial Drainage Catheter
J. Med. Devices (June,2011)
Experimental Techniques for Studying Poroelasticity in Brain Phantom Gels Under High Flow Microinfusion
J Biomech Eng (May,2010)
Innovation and Design: Pollution Prevention Opportunities in Medical Device Design
J. Med. Devices (June,2009)
Stimuli-Responsive Triblock Polymers for Multipulse Drug Delivery
J. Med. Devices (June,2009)
Related Proceedings Papers
Related Chapters
Surface Analysis and Tools
Tribology of Mechanical Systems: A Guide to Present and Future Technologies
Application of Kelvin Force Microscopy Measurements and Secondary Ion Mass Spectroscopy to Evidence Hydrogen Embrittlement for the 2024 Aluminum Alloy
International Hydrogen Conference (IHC 2012): Hydrogen-Materials Interactions
Nanomaterials: A brief introduction
Biocompatible Nanomaterials for Targeted and Controlled Delivery of Biomacromolecules