Capacity control in most commercial centrifugal chillers is achieved by inlet guide vanes which are activated by the leaving chilled water temperature sensor. Due to mechanical reasons, vane control is done discretely, and not continuously. The control module compares the value provided by the temperature sensor to pre-set control band values, and if those bands are exceeded, it sends a signal to the vane control motor to adjust the vane position by one step which could be upwards or downwards. The advantage of this type of discrete control method is its simplicity. Normally, the accuracy in the outlet chilled water temperature is of the order of which is acceptable for normal cooling plants such as used in office buildings. However, there are applications such as in pharmaceutical processes, mechanics labs, or instances in chemical processes where more accurate control is required (sometimes as low as This paper proposes a simple method to achieve such tight control without any hardware modifications. The basis of this method is a transient physical inverse model of the refrigerant boiling process in the evaporator, in conjunction with a feed-forward control scheme. The model parameters need to be identified from monitored data since they are chiller-specific. This paper describes the model, and applies it to one-minute monitored data from an actual chiller plant of 1580 kW (450 Tons). It is demonstrated that for this specific chiller such a control scheme has the potential to improve control accuracy by about 28% as compared to the traditional control method.
Skip Nav Destination
Article navigation
February 2005
Technical Papers
A Model-Based Feed-Forward Controller Scheme for Accurate Chilled Water Temperature Control of Inlet Guide Vane Centrifugal Chillers
Yongzhong Jia,
Yongzhong Jia
Department of Mechanical Engineering and Mechanics, 3141 Chestnut St., Drexel University, Philadelphia, PA 19104
Search for other works by this author on:
T. Agami Reddy
T. Agami Reddy
Department of Mechanical Engineering and Mechanics, 3141 Chestnut St., Drexel University, Philadelphia, PA 19104
Search for other works by this author on:
Yongzhong Jia
Department of Mechanical Engineering and Mechanics, 3141 Chestnut St., Drexel University, Philadelphia, PA 19104
T. Agami Reddy
Department of Mechanical Engineering and Mechanics, 3141 Chestnut St., Drexel University, Philadelphia, PA 19104
Contributed by the Solar Energy Division of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF SOLAR ENERGY ENGINEERING. Manuscript received by the ASME Solar Division November 4, 2003; final revision April 7, 2004. Associate Editor: M. Krarti.
J. Sol. Energy Eng. Feb 2005, 127(1): 47-52 (6 pages)
Published Online: February 7, 2005
Article history
Received:
November 4, 2003
Revised:
April 7, 2004
Online:
February 7, 2005
Citation
Jia , Y., and Reddy, T. A. (February 7, 2005). "A Model-Based Feed-Forward Controller Scheme for Accurate Chilled Water Temperature Control of Inlet Guide Vane Centrifugal Chillers ." ASME. J. Sol. Energy Eng. February 2005; 127(1): 47–52. https://doi.org/10.1115/1.1775225
Download citation file:
Get Email Alerts
Cited By
Analysis of Erosion of Surfaces in Falling Particle Concentrating Solar Power
J. Sol. Energy Eng (April 2025)
Related Articles
Model of Human/Liquid Cooling Garment Interaction for Space Suit Automatic Thermal Control
J Biomech Eng (February,2001)
Autonomous Thermal Control System for Highly Variable Environments
J. Heat Transfer (June,2009)
On the Development of a Low Cost Pyrheliometer
J. Sol. Energy Eng (August,2011)
Thermal Model of an Absolute Solar Radiometer Designed for Future Satellite Missions
J. Sol. Energy Eng (February,2001)
Related Proceedings Papers
Related Chapters
Reservoir Water Level Detection Based on Optical Fiber Temperature Sensor
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)
Cooling a Radar’s Electronic Board
Electromagnetic Waves and Heat Transfer: Sensitivites to Governing Variables in Everyday Life
Thermodynamic Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential