Abstract

The amount of lubricating oil in a gear reducer greatly influences components’ temperature and efficiency of the reducer. A thermal network simulation model of a gear reducer for electric vehicles based on amesim software was built for thermal and efficiency analysis of the reducer, where heat production and transfer processes of each component in the reducer are considered. Moreover, secondary development submodels were developed to calculate the convection coefficients in real time based on different lubricating oil temperatures and working conditions. Next, the experiments were conducted to verify the developed model regarding transmission efficiency and lubricating oil equilibrium temperature in the reducer. The deviation between the numerical and experimental results is less than 5%, which indicates high accuracy of the developed thermal network model. Thereafter, efficiency and heat balance simulation tests under different working conditions were performed to determine an optimal lubricating oil supply, which is 14 mm gear-oil-immersion oil supply in this study. Finally, a comparison between the reducer with the optimal oil supply and that with normally used 22 mm gear-oil-immersion supply in the NEDC cycles in low temperature was done. The reducer with the optimal oil supply shows 1.032% energy saving. The method presented in this article provides a good guide to design and optimization of the gear reducer for electrical vehicles.

References

1.
Chang
,
C.-M.
, and
Siao
,
J.-C.
,
2010
, “
Performance Analysis of EV Powertrain System With/Without Transmission
,”
World Electr. Veh. J.
,
4
(
3
), pp.
629
634
.
2.
Wang
,
B.
,
Lu
,
Z. J.
,
Chen
,
X. B.
,
Wang
,
P.
,
Luo
,
W.
, and
Xu
,
H.
,
2015
, “
Modeling and Analysis of the Dynamic Efficiency of Manual Transmission/Reducer
,”
Int. J. Automot. Technol.
,
16
(
3
), pp.
417
426
.
3.
Yang
,
S.
,
Reddyhoff
,
T.
, and
Spikes
,
H.
,
2013
, “
Influence of Lubricant Properties on ARKL Temperature Rise and Transmission Efficiency
,”
Tribol. Trans.
,
56
(
6
), pp.
1119
1136
.
4.
Shin
,
J. W.
,
Kim
,
J. O.
,
Choi
,
J. Y.
, and
Oh
,
S. H.
,
2014
, “
Design of 2-Speed Transmission for Electric Commercial Vehicle
,”
Int. J. Automot. Technol.
,
15
(
1
), pp.
145
150
.
5.
Li
,
S.
,
2015
, “
A Thermal Tribo-Dynamic Mechanical Power Loss Model for Spur Gear Pairs
,”
Tribol. Int.
,
88
, pp.
170
178
.
6.
Yuksel
,
T.
, and
Michalek
,
J. J.
,
2015
, “
Effects of Regional Temperature on Electric Vehicle Efficiency, Range, and Emissions in the United States
,”
Environ. Sci. Technol.
,
49
(
6
), pp.
3974
3980
.
7.
Liu
,
H.
,
Liu
,
H.
,
Zhu
,
C.
, and
Parker
,
R. G.
,
2020
, “
Effects of Lubrication on Gear Performance: A Review
,”
Mech. Mach. Theory
,
145
, p.
103701
.
8.
Ai
,
S.
,
Wang
,
W.
,
Wang
,
Y.
, and
Zhao
,
Z.
,
2015
, “
Temperature Rise of Double-Row Tapered Roller Bearings Analyzed With the Thermal Network Method
,”
Tribol. Int.
,
87
, pp.
11
22
.
9.
Chen
,
C. M.
, and
Kovacevic
,
R.
,
2003
, “
Finite Element Modeling of Friction Stir Welding—Thermal and Thermomechanical Analysis
,”
Int. J. Mach. Tools Manuf.
,
43
(
13
), pp.
1319
1326
.
10.
Latif
,
M.
, and
Bryant
,
P. R.
,
2004
, “
Network Analysis Approach to Multidimensional Modeling of Transistors Including Thermal Effects
,”
IEEE Trans. Comput. Aided Des. Integr. Circuits Syst.
,
1
(
2
), pp.
94
101
.
11.
Lin
,
Z. J.
,
Yuan
,
J. H.
,
Li
,
Y.
,
Yan
,
X. J.
,
Zhou
,
S. M.
,
Chen
,
R. J.
,
2013
, “
A Temperature Field Model of Complicated Thermal Analysis System Based on Thermal Network Method
,”
Adv. Mater. Res.
,
694–697
, pp.
695
698
.
12.
Xiaozhou
,
H. U.
,
Shaojun
,
L.
, and
Jie
,
P.
,
2015
, “
Steady State Thermal Analysis of Transmission Shaft System of Main Reducer of Helicopter
,”
J. Cent. South Univ.
,
46
(
12
), pp.
4469
4475
.
13.
Chen
,
C.
,
2013
, “
Power Flow and Efficiency Analysis of Epicyclic Gear Transmission With Split Power
,”
Mech. Mach. Theory
,
59
, pp.
96
106
.
14.
Conejo
,
A. J.
,
Arroyo
,
J. M.
,
Alguacil
,
N.
, and
Guijarro
,
A. L.
,
2007
, “
Transmission Loss Allocation: A Comparison of Different Practical Algorithms
,”
IEEE Power Eng. Rev.
,
22
(
5
), pp.
66
66
.
15.
Hölm
,
B.-R.
,
Miclwelis
,
K.
,
Collenberg
,
H.
, and
Schlenk
,
L.
,
2001
, “
Effect of Temperature on the Scuffing Load Capacity of EP Gear Lubricants
,”
Tribotest
,
7
(
4
), pp.
317
332
.
16.
Diab
,
Y.
,
Ville
,
F.
, and
Velex
,
P.
,
2006
, “
Investigations on Power Losses in High-Speed Gears
,”
Proc. Inst. Mech. Eng. Part J: J. Eng. Tribol.
,
220
(
3
), pp.
191
198
.
17.
Ruzek
,
M.
,
Ville
,
F.
,
Velex
,
P.
,
Boni
,
J. B.
, and
Marchesse
,
Y.
,
2019
, “
On Windage Losses in High-Speed Pinion-Gear Pairs
,”
Mech. Mach. Theory
,
132
, pp.
123
132
.
18.
Anderson
,
N. E.
, and
Loewenthal
,
S. H.
,
1986
, “
Efficiency of Nonstandard and High Contact Ratio Involute Spur Gears
,”
ASME J. Mech. Des.
,
108
(
1
), pp.
119
126
.
19.
Hamrock
,
B. J.
, and
Jacobson
,
B. O.
,
1984
, “
Elastohydrodynamic Lubrication of Line Contacts
,”
ASLE Trans.
,
27
(
4
), pp.
275
287
.
20.
Changenet
,
C.
,
Leprince
,
G.
,
Ville
,
F.
, and
Velex
,
P.
,
2011
, “
A Note on Flow Regimes and Churning Loss Modeling
,”
ASME International Design Engineering Technical Conferences & Computers & Information in Engineering Conference
,
Washington, DC
,
Aug. 28–31
, pp.
549
555
.
21.
Palmgren
,
A.
,
1946
,
Ball and Roller Bearing Engineering
,
SKF Industries
,
Philadelphia, USA
.
22.
Yang
,
S.
,
2006
,
Heat Transfer
, 4th Ed.,
Higher Education Press
,
Beijing
.
23.
Cardone
,
G.
,
Astarita
,
T.
, and
Carlomagno
,
G. M.
,
2007
, “
Heat Transfer Measurements on a Rotating Disk
,”
Opt. Diagn. Eng.
,
3
(
1
), pp.
1
7
.
24.
Handschuh
,
R. F.
, and
Litvin
,
F. L.
,
1991
, “
A Method for Determining Spiral-Bevel Gear Tooth Geometry for Finite
,”
NASA Technical Reports
,
Cleveland, OH
,
Aug. 1
,
Report No. 3096
.
25.
Harris
,
T. A.
, and
Mindel
,
M. H.
,
1973
, “
Rolling Element Bearing Dynamics
,”
Wear
,
23
(
3
), pp.
311
337
.
26.
Henneberg
,
M.
,
Eriksen
,
R. L.
,
Jørgensen
,
B.
, and
Fich
,
J.
,
2015
, “
A Quasi-Stationary Approach to Particle Concentration and Distribution in Gear oil for Wear Mode Estimation
,”
Wear.
,
324–325
, pp.
140
146
.
27.
Gillot
,
R.
,
Dempsey
,
M.
, and
Picarelli
,
A.
,
2015
, “
Predicting the Effect of Powertrain Preconditioning on Vehicle Efficiency
,”
Math. Model. Anal.
,
23
(
1–3
), pp.
301
318
.
You do not currently have access to this content.